|
Feature Webseite |
Universal 6380A/6388A/6389A |
Panasonic RHS2 |
Panasonic RH 5 |
Insertion Rate |
16,000 CPH | 18,000 CPH | 12,400 CPH |
| Tact Time | 0.225 sec Constant Speed | 0.2 sec Maximum (0.25 sec for the component with 12mm diameter and 18mm height or bigger) | 0.29 sec Maximum (Speed slows depending on component type.) |
4 Axis Insertion |
Yes, by rotating insertion head and/or table. Head rotates in three directions; -90, 0, and +90 degrees. | Yes, the insertion head can rotate in four directions: 0, -90, +90, and 180 degrees. | Yes, but optional.
(Standard Only) 0, 90 Degrees by Head |
Rotary Table |
Yes, 90 and 180 Degree Increments | No – Head Rotates 3600 | No |
Insertion Span |
2.5/5.0mm Dual Span
2.5/5.0/7.5 or 5.0/7.5/10.0 Triple Span |
2.5/5.0mm | 2.5/5.0mm |
| Maximum Body Diameter/Height (Height measured from center of feedhole to top of component.) | 13.0mm/38.5mm | 13mm/39mm | 13mm/39mm |
| Board Handling Transfer Time (from the last insertion of the first PCB to the first insertion of the second PCB, including table movement) | 3.5 seconds | 4 to 5 seconds | 5 to 6.5 seconds (NM 8245 A,B,C)
4 to 5.5 seconds (NM 8244 A,B,C) |
| Maximum Board Size | 559 x 470mm (NPT)
483 x 406mm (PT) |
508mm x 381mm | 508mm x 381mm (NM 8245 A,B,C) 330mm x 250mm (NM 8244 A,B,C) |
| Insertion Area | 470 x 470mm (NPT)
470 x 406mm (PT) |
508mm x 371mm | 508mm x 371mm (NM 8245 A,B,C) 330mm x 240mm (NM 8244 A,B,C) |
| Allowable PCB Thickness | 0.79mm to 2.36mm | 1.6 +/- 0.15mm standard
The RHS can accommodate a range of 0.8 to 2.0mm, however the PCB transfer rails must be changed for PCBs with nonstandard thickness. This is an option. Even when using the standard 1.6mm thick PCB, there are chances of lead length/angle variation which causes PCB transfer error depending on the shapes of boards and/or insertion holes. |
1.6 +/- 0.15mm standard
The RH5 can accommodate a range of 0.8 to 2.0mm, however the PCB transfer rails must be changed for PCBs with nonstandard thickness. This is an option. Even when using the standard 1.6mm thick PCB, there are chances of lead length/angle variation which causes PCB transfer error depending on the shapes of boards and/or insertion holes. |
| PCB Warpage | Maximum of 3.17mm downward and 1.6mm upward | Maximum of 1.2mm downward and 0.5mm upward | Maximum of 1.2mm downward and 0.5mm upward |
Part Transfer Method |
Sequencer | Sequencer | Shuttle |
| Number of Input Stations | 20, 40, 60, 80, 100 | 80 | 40, 62 (Single Shuttle)
80 (Dual Shuttle) |
Component Supply |
Reels or ammo packs on any input. | Reels or ammo packs. Reels can only be used on the lower input bank (40 station). | Reels or ammo packs. Reels can only be used on the lower input bank |
| Component Taping Pitch | 12.7/15/25.4**/30mm** | 12.7/15.0mm | 12.7/15.0mm |
| Odd Form Component Insertion | Yes, at a constant rate of speed | Yes, but at a derated insertion speed, dependent on component shape/size. | Yes, but at a derated insertion speed, dependent on component shape/size. |
Verification |
Yes, value polarity. | No | No |
| Board Error Correction | Yes, Standard | Yes | Yes |
| Low Part Warning | Yes, Standard | No | No |
| Insertion Density | Tooling effects footprint. | Tooling effects footprint. | 0.5mm on all sides–use of guide pins allows for same insertion density capabilities regardless of component |
| Auto Recovery | Yes – Semi-Automatic | Yes – Interrupt Recovery Enabled (Automatic supply recovery function) | Yes – Fully Automatic |
| Component Replenishment | Any disp.head location can be spliced w/o stopping the machine. | Although this is a sequencer based machine, when a feeder is low on components, that feeder and the two adjacent feeders must be turned off before reloading or splicing additional components. If during the reloading process the machine requires components from those three feeders, the machine stops until the reloading process is completed by the operator. | Machine needs to be stopped for component replenishment. |
| Uninterrupted Power Supply | Standard. When the UPS detects a power interruption, its fully-charged battery can run the machine for up to 10 minutes. | No | No |
Language |
English is the main language, however Chinese is available for event messages. | Japanese/English | Japanese/English |
| Machine Dimensions | 80 Stations (In-line):
W = 5428mm D = 3226mm H = 1746mm
80 Stations (Straight Back): W = 1800mm D = 6397mm H = 1746mm |
80 Stations:
W = 3125mm D = 2210mm H = 1560mm |
NM-8244C (80 Sta):
W = 5160mm D = 1860mm H = 1650mm
NM-8245C (80 Sta): W = 5160mm D = 2110mm H= 1600mm
|
| Marketing Evaluation | 2 years with more than 200 installed machines worldwide, good public praise | Brand new machine without marketing evaluation | New machine with few marketing evaluation |
** Capable of processing 25.4 mm and 30 mm pitch taped components.